Close

Search:

Type: Posts; User: ajm8127

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    67
    Views
    5,763

    I went out to start my car yesterday to go get...

    I went out to start my car yesterday to go get some wine for a diner party at my neighbor's house. I fired it up and the idle was oscillating between about 800 and 1400 rpm. The pedal was...
  2. Replies
    148
    Views
    7,656

    That's probably not the case because T-6 has a...

    That's probably not the case because T-6 has a higher concentration of ZDDP and phosphorous can lower the life expectancy of three way catalysts so LL-01 oils have been developed with less ZDDP....
  3. Replies
    148
    Views
    7,656

    I use the T6 and have had good results according...

    I use the T6 and have had good results according the UOA with a tuned, stock turbo car. More phosphorous and zinc (ZDDP) than an LL-01 oil because they have been removing ZDDP to prevent damage to...
  4. Replies
    198
    Views
    15,878

    Glad to hear you are OK. There will always be...

    Glad to hear you are OK. There will always be more cars to build. Hobbies are merely a way to occupy our spare time not spent doing the things that matter most. I can sympathize with your labor of...
  5. Replies
    11
    Views
    360

    E90,E91,E92,E93: If you are set on keeping this car, the...

    If you are set on keeping this car, the suspension is where I would focus most of my time and money. It will never be powerful like a forced induction car, and if you want to put forced induction on...
  6. Replies
    122
    Views
    8,202

    I was thinking those coolant passages look very...

    I was thinking those coolant passages look very interesting, then I looked at some pictures of the head.

    46557
  7. Replies
    52
    Views
    3,244

    Oh. My. God.

    Oh. My. God.
  8. Replies
    198
    Views
    15,878

    Nice work on the electrical. There is nothing...

    Nice work on the electrical. There is nothing like custom built harnesses to make a project look finished. Going the extra step and using heat shrink tubing takes the quality beyond most OEM. The...
  9. The question was if the sensor actually tests the...

    The question was if the sensor actually tests the quality of the oil. It does. The sensor has a capacitor built in that is used to measure the dielectric constant of the oil. Read why that is...
  10. Replies
    369
    Views
    7,506

    Agreed. I love getting dirty and putting my face...

    Agreed. I love getting dirty and putting my face right under the hood. Girls are cool too.
  11. Replies
    27
    Views
    1,855

    I would try to come to an amicable solution with...

    I would try to come to an amicable solution with the supplier of the turbos. Posting their name here will definitely not help.

    I agree with RSL fatigue would have taken what I would think would...
  12. Replies
    27
    Views
    1,855

    Another possibility is an error in assembly. ...

    Another possibility is an error in assembly.

    Did you find the nut? It can't get too far. Or maybe it was destroyed by the blades, though they are aluminum and the nut should be steel.
  13. I was pretty sure I head read some where, and the...

    I was pretty sure I head read some where, and the document here (http://www.bimmerforums.com/forum/showthread.php?954499-BMW-oil-change-sensing-system) confirms it, but the sensor measures level and...
  14. Replies
    49
    Views
    20,916

    Sticky: I am not sure on the processor, but pre 03/07 is...

    I am not sure on the processor, but pre 03/07 is most likely different than post 03/07. I say this because the Alpina code works in one but not the other. Unless the change is just the supporting...
  15. Could it have to do with the rate of change of...

    Could it have to do with the rate of change of engine speed? "RPM Dynamic" implies to me the engine is changing speed.

    Maybe zero it out and see what happens.
  16. That honestly surprises me. I have gotten in the...

    That honestly surprises me. I have gotten in the habit of using anti-seize on most fasteners especially in the suspension, though when I initially took my front suspension apart to install the M3...
  17. Replies
    154
    Views
    9,546

    Looks good. Something I didn't think about when I...

    Looks good. Something I didn't think about when I had my engine suspended, but did you loop that chain around as a backup means of support should the hooks on the screw part of the engine bar fail?
  18. Emphatically, YES! I wouldn't expect too...

    Emphatically, YES!



    I wouldn't expect too much rust. Most of the fasteners are galvanized. I live in PA where they liberally use salt during the winter and I haven't had too much trouble.
  19. Replies
    13
    Views
    748

    In this one you can pretty clearly see boost mean...

    In this one you can pretty clearly see boost mean abs going way above req boost abs. The DME shuts the throttle and throws a code. In my opinion this doesn't look like a Base WDGC table that is a...
  20. It can be done without dropping the subframe and...

    It can be done without dropping the subframe and I have done three turbo swaps that way, but after replacing my oil pan gasket and having to drop the subframe for that I would never swap turbos again...
  21. Replies
    118
    Views
    7,314

    Easy mistake to make and an equally simple...

    Easy mistake to make and an equally simple solution.
  22. Replies
    13
    Views
    748

    Use datazap.me to post the logs. There is a...

    Use datazap.me to post the logs.

    There is a thread around about logging with a Cobb AccessPort. Read that one and look through the "How To Cobb ATR discussion" thread. Both are stickied.

    You...
  23. Replies
    17
    Views
    794

    N55: The N63 has all kinds of problems. Timing chain,...

    The N63 has all kinds of problems. Timing chain, fuel system, oil consumption. There is a not a recall on the engine because BMW wouldn't do that unless there was a safety problem (for liability...
  24. Replies
    13
    Views
    851

    E90,E91,E92,E93: I see you tried a u-bolt. I would think that...

    I see you tried a u-bolt. I would think that could work if you replaced the flat piece with a piece of angle steel. I am sure that flat piece bent pretty quickly.

    Or maybe use a muffler clamp of...
  25. Replies
    21
    Views
    1,224

    E90,E91,E92,E93: That sounds like a lot of fun. Nice and flat, not...

    That sounds like a lot of fun. Nice and flat, not much to run into...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4