Close

Search:

Type: Posts; User: ajm8127

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    244

    44988 First you have the human sex trade...

    44988

    First you have the human sex trade objectifying women, and now not even poultry get the dignity they deserve.

    Or am I missing something?
  2. Replies
    11
    Views
    220

    For whatever reason the design of the 12 mm seal...

    For whatever reason the design of the 12 mm seal required the sealant, but the 8 mm seal does not. I believe the sealant was meant to ensure a leak free seal at the interface between the block and...
  3. Replies
    11
    Views
    220

    I have no problems with the seal I installed. My...

    I have no problems with the seal I installed. My car is daily driven and has about 7000 miles on it since the seal install. Get some large washers (I used McMaster 90107A036 not because they are...
  4. If I remember correctly I got kind of lucky and...

    If I remember correctly I got kind of lucky and saw someone (sammy_0559 I think) was selling theirs for whatever reason. I jumped on it and rebuilt it using the Sonnax Zip Kit. It's been performing...
  5. Replies
    13
    Views
    266

    Did you test for voltage on the solenoid wire...

    Did you test for voltage on the solenoid wire when you press the button?
  6. Replacing and coding the mechatronics module is...

    Replacing and coding the mechatronics module is actually not all that hard. You can download all the software online. Just have to replace 5 or 6 seals between the transmission body and valve body....
  7. Replies
    13
    Views
    266

    It is under the intake manifold which will have...

    It is under the intake manifold which will have to be removed, which means charge pipe, throttle body, DVs, etc. need to also be removed. You need some e-torx sockets and a swivel ratchet will make...
  8. Replies
    6
    Views
    141

    Did the bolts get tightened in the correct order...

    Did the bolts get tightened in the correct order after making them all finger tight? Check the Zf Mechatronic Replacement guide in the 6HP21 Reference Docs sticky for the pan replacement tightening...
  9. Replies
    13
    Views
    266

    I spent three or four days carrying around an 18"...

    I spent three or four days carrying around an 18" breaker bar and hammer to smack the starter to loosen the brushes when I was having starting trouble. If you've got power to the solenoid wire (the...
  10. Looks like an electrical issue. Goes away and...

    Looks like an electrical issue. Goes away and comes back randomly and you are getting codes for lots of things like crank sensor, manifold sensor, tank vent valve, fuel pressure control valve. Points...
  11. How much oil are you consuming? Is there anything...

    How much oil are you consuming? Is there anything else that coincided with the increase in consumption like tuning the car or just choosing a more aggressive map?

    I had a similar problem after...
  12. S63/S63TU: I am willing to bet you would not be able to...

    I am willing to bet you would not be able to distinguish a difference in the before and after temperature from the noise in the data. It already looks to be a "cold air" style intake. How much heat...
  13. Replies
    30
    Views
    790

    If you remove aluminum bolts and replace them...

    If you remove aluminum bolts and replace them with steel, angle tightening is not required and should not be used. I would guess if you angle tightened steel bolts in an aluminum engine, you would...
  14. Replies
    4
    Views
    351

    LOL, I thought that was Jackie Stewart. "I don't...

    LOL, I thought that was Jackie Stewart. "I don't believe in bad luck, just poor preparation." What a great quote.
  15. Replies
    30
    Views
    790

    Installing the seal is not that difficult. All...

    Installing the seal is not that difficult.

    All you need is the old seal, half the crank bolts, an equal number of large washers and a little bit of patience to install the RMS. It's not as super...
  16. Thread: o2 sensors

    by ajm8127
    Replies
    4
    Views
    246

    The 2C6B is a secondary bank 1 O2 "system check"...

    The 2C6B is a secondary bank 1 O2 "system check" code. The other codes are bank 1 and 2 primary O2 sensor trim codes. I have read the response time of O2 sensors can slow over time.

    I don't know...
  17. Replies
    354
    Views
    9,230

    Exactly. That picture is pretty fancy, but the...

    Exactly. That picture is pretty fancy, but the pipe should at least neck down in the area the fitting is welded in. You need to speed up the gas sufficiently so slight vacuum is generated relative to...
  18. Replies
    30
    Views
    790

    That's an interesting picture. You think...

    That's an interesting picture. You think crankcase pressure forced it out? I am pretty sure that is what happened to mine.
  19. Replies
    30
    Views
    790

    I would do the rear main seal as well. I did mine...

    I would do the rear main seal as well. I did mine and used four crank bolts and the old seal to install the new seal. The old seal had completely lost its elasticity.
    ...
  20. Replies
    44
    Views
    1,128

    E82/E88: I imagine something like that would work fine. ...

    I imagine something like that would work fine.

    If you are an AT and intend to do some hot laps, you are limiting the life of your transmission by not using an axillary cooler. Because my car is a...
  21. Replies
    44
    Views
    1,128

    E82/E88: I didn't know these existed but there are tools...

    I didn't know these existed but there are tools that allow you to form a bead in a rigid tube by hand.

    http://www.efihardware.com/images/medium/1248/EZ-bead-tool-38-tubing_1248.jpg

    Earl's...
  22. Replies
    44
    Views
    1,128

    E82/E88: I plan to install an ATF cooler in front of the...

    I plan to install an ATF cooler in front of the driver's wheel opposite the engine oil cooler. That's right where the PPK rad goes though.

    There are two steel lines that run on the left side of...
  23. I think it is interesting and obviously it is a...

    I think it is interesting and obviously it is a concept so a production version would probably look a bit different. Besides the color, I like the looks. I am sure BMW does not want to take sales...
  24. Replies
    44
    Views
    1,128

    E82/E88: Do you need an aux rad for engine coolant? You...

    Do you need an aux rad for engine coolant? You can get the engine coolant temp to show up in the cluster to monitor temperature in real time.


    https://www.youtube.com/watch?v=DAd86TnqxWc

    I...
  25. LOL, sometimes I just flows. Where are you...

    LOL, sometimes I just flows.

    Where are you going to get 24 volts? Sure you could use a boost regulator, but that adds inefficiency and cost. The only reason you would use more voltage is if you...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4